Once it starts fogging, leave the room and close the door. To use Fog U as a mold bomb fogger, place the can in the center of the room, inside crawl space, ductwork, or wherever you need it and press down until you hear a click. One can treats an area of up to 10′ x 10′ (800 cubic feet), provides months of protection, and is perfectly safe for use around people and pets. It has a 360° nozzle that you can use as a total release fogger or spray can. Open the windows and doors after fogging has been completed, and wait a little while for the fog to dissipate.įog U Mold Cleaner kills mold, mycotoxins, mildew, bacteria, and allergy-causing particles with natural enzymes while deodorizing. It’s best not to be in the room while fogging, even if the solution used is natural and non-toxic. Please note: Atomized particles released by mold bomb foggers float in the air for long periods of time and are easily absorbed through the lungs. The best mold bomb fogger is Fog U – which is non-toxic, highly effective against mold and their spores, and safe to use around humans and pets. Leave the room and close the door.Ĥ: Switch the machine off once the fogger has finished and wait approximately 30 minutes for the fog to dissipate before opening the windows. Set the nozzle to release the fog at a 60-degree angle and set the density of the fog on the finest possible setting.ģ: Make sure no one is in the room (pets included), and start the machine. Close all windows and remove or cover/remove any sensitive items (paper).Ģ: Add your mold fogging solution into the tank and set your desired settings (density of the fog and timer). How to use a ULV (Ultra Low Volume) fogger safely and correctlyġ: Place the ULV fogger in the center of the room, close the windows, and clear any obstructions that may be in the way. Leave the room and close the door for 2 hours while it sanitizes and disinfects.Ĥ: Once sufficient time has passed, enter the room, open the windows and discard the can. It will give you a couple of seconds to leave the room before the fog gets released. Also, no humans or pets are to be in the room during fogging – even if the fogging solution is non-toxic.ģ: Set the fogger off as per instructions on the can. Close all windows and remove or cover/remove any sensitive items (paper). If the room has more square meters than the fogger can handle, then you may want to consider using two cans.Ģ: Place the can in the center of the room and clear any obstructions. How to use a mold bomb fogger safely and correctlyġ: First, check the can to see how many square meters the mold bomb can fog. It kills up to 99% of all bacteria and viruses such as covid-19, herpes, H1N1 influenza, HIV, and so much more. It sanitizes and disinfects: The chemicals contained in these products kill so much more than just mold and mildew. It’s an excellent preventative measure: You don’t always have to wait for mold to appear before taking action, because setting off a mold bomb fogger in high-risk parts of your home on occasion is a great preventative measure. Crawl spaces, the inside of air conditioners, and attics are just a few examples of such places. It kills mold in hard-to-reach places: Mold hates the light and thus usually thrives in dark areas that are out of sight and hard to reach. The chemicals that a mold bomb fogger releases kill these spores, which stops further colonization. It kills mold spores: Once mold starts growing in your home, it will begin spreading quickly by releasing spores into the air that colonizes other areas. Why use a mold fogger? A bad mold infestation. In this article we won’t be covering thermal fogging, because it’s not as DIY friendly as the ULV and aerosol can methods – mainly because it uses a lot of heat to create atomized particles and it can therefore be a fire hazard. These particles can reach even the most hard-to-reach places and kills all mold upon contact.Īlso, the smaller the atomized particles in the fog are, the more effective it will be. Also, when in in the air they attach themselves to mold spores, mycotoxins, bacteria, and other allergy causing particles, kills them and then weighs them down to the ground and onto surface areas. The particles spread throughout the room and cover all surface areas and walls. It releases it as a fog (atomized particles measured microns in size) into the air. They contain a mold fogging solution in liquid form. They all do the same thing, which is release atomized particles into the air that kills bacteria, viruses, mold, and spores from surface areas and the air, while some even deodorize to get rid of any unpleasant mold and mildew smells. There are three types of mold foggers – one releases fog from an aerosol can (mold bomb fogger) and the other from a small machine – ULV cold foggers and thermal foggers. What are mold bombs, ULV, and thermal fogging?
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |